TOP PAD BAGS

Call 1-800-333-PITS to see how this time saving new piece of equipment can add years to the life of your pit as well as make handling the most awkward part of the setup easy.

Frequently Asked Questions

In an effort to make information more readily available, please submit any questions so we can post answers to help everyone.

Should I put my pit up on pallets to help drain water?

Pallets are a bad idea for several reasons. First, pallets are not part of the pit; they didn't come with the pit, nor were they intended to be used to hold up a pit for pole vault or high jump competition. In the pole vault, they create an area around the box of unpadded wood and negate the effectiveness of the now-required box collar. For those pits with the collar "built in," putting four inches of wood under this built in collar is also counterproductive. If an athlete gets into a pallet and is injured, a huge liability issue arises.

But pallets get worse for the pole vault. Our pits (like many in the industry) are designed so that the angles around the vaulting box facilitate the flex in the pole. By raising the bottom of the pit the height of a pallet, the chance of the pole touching the pallet or the pit is greatly increased. Along those lines, if a vaulter misses the box with the end of the pole, having a pallet under the pit increases the chance of the pole wedging under the pit and breaking. With the rising cost of poles, this can prove to be a costly mistake.

Why do so many companies suggest raising the pit then? Many claim that water can damage the foam and fabric and cause early wear to the pit. This simply isn't the case; at least not with a a Richey pit. We use 22 oz. vinyl coated nylon, coated on both sides. Vinyl isn't adversely affected by water (that's why they make swimming pool liners out of vinyl). To the same degree, our foam isn't hurt by water either. Foam and vinyl fabric's greatest weakness is how they handle ultra violet light; that is to say, the sun will fry your pit before the rain ever touches it.

We've repaired more pits that have been cut by the corners of a pallet, or torn by a stray pallet staple or nail, than pits that have been damaged by any other means. Put your pit directly on the ground and save your money.

My weather cover leaks and it's brand-new. Is it defective?

When you put a dark colored weather cover over a pit, it attracts heat from the sun. When the pit blocks the sun from the ground, the ground stays cool. Hot pit over the top of a cold ground and conditions are prime for condensation to occur; and it will occur by the gallon. But as stated earlier, it's not water that hurts the pit, it's the sun. So turn the pit over to drain if it fills up too much, but keep the weather cover on it to keep the sun off of it.

My pit is pooling water in the center of the weather cover. What should I do?

The short answer it, rotate the back sections. Moving the section in the middle whose soft spot is allowing the water to pool to an edge will allow that water to run off of the edge of the pit rather than further crush your pit.

The longer answer is for those of you who do not have a pit whose back sections are interchangeable. In this case, you might find it helpful to purchase one of the center supports the company you bought your pit from manufactures. They'll prop up the center of the weather cover to allow for enough of a slope for the water to run off. If this extra expense is not feasible, then we suggest grabbing a hurtle from the track and tipping it on it's side under the weather cover. This should raise the middle of the cover enough to allow the rain water to run off.

What we do not suggest is trying to raise that center section by placing pallets underneath of just that center section. This will raise the top pad in the center and cause undue stress on the snaps along the edge during competition, shortening the life of your pit. Not to mention your vaulters no longer have a smooth top surface to land on; creating more slopes and valleys, especially in the primary landing area, is a good way for an athlete to turn an ankle.

How are the back sections of a pit's foam constructed?

The back sections of foam are made of a solid top layer and two more layers of crosshatched pillars underneath. As opposed to a solid back piece of foam, this allows for varying densities of foam to be used as well as keeps the back sections light enough to easily move around. It also keeps the cost down by saving several hundred board feet of foam that would have filled the spaces in between.

For more information or a quote: Click Here

E-Mail-

info@richeyathletics.com

Toll-Free at--

1-800-333-PITS

By Mail-

Max Richey

Richey MFG

P.O. Box 166

Michigantown, IN

46057

Fax-

765-249-3010